4 hours ago Jan 13, 2016 . AT Check if the command terminal work normally * AT+RESET Software reboot * AT+VERSION Get firmware, bluetooth, HCI and LMP version * AT+HELP List all the commands * AT+NAME Get/Set local device name * AT+PIN Get/Set pin code for pairing * AT+PASS Get/Set pin code for pairing * AT+BAUD Get/Set baud rate * AT+LADDR Get local bluetooth address *
Show more
See More
3 hours ago Contacts. LISTEN BY PHONE: 1.605.615.0901 and 1-631-359-8204. HM on ZenoRadio. HM on APP STORE. HM on GOOGLE PLAY. LIVE from New York - Listen by phone at 1.605.615.0901. HM RADIO. Schedule. Archive.
username
Show more
See More
10 hours ago The HM-10 has 10 pins that can be user controlled, a couple are input only, the others can be input or output. Unfortunately, the pins we can control are not available on the breakout board so we need to attach a connection directly to the actual HM-10 (the small daughter board). Pin function. The pins we can use are PIO-2 to PIO-11(B).
Show more
See More
6 hours ago Isophon, E. Fritz & Hochton-Lautsprecher HM10 (2) Rimpex-Katalog, 1966 Technical Specifications Wave bands - without Power type and voltage No Power needed Loudspeaker Permanent Magnet Dynamic (PDyn) Loudspeaker (moving coil) / Ø 10 cm = 3.9 inch Material Metal case from Radiomuseum.org
Dimensions (WHD): 100 x 50 x 100 mm / 3.9 x 2 x 3.9 inch
Shape: Chassis only or for «building in»
Material: Metal case
username
Show more
See More
2 hours ago May 02, 2018 . The HM-10 is a readily available Bluetooth 4.0 module based on the Texas Instruments CC2540 or CC2541 Bluetooth low energy (BLE) System on Chip (SoC). The module design and firmware originated from the Jinan Huamao Technology Company (JNHuaMao), but is sold by various Chinese suppliers, and by several U.S.and European distributors.
Show more
See More
11 hours ago The HM-10 XD microphone comes equipped with a microphone clip and a foam windscreen. A CC-1 adapter is required to interface with your transceiver. To achieve optimal tailored response for the HM-10 XD you will need to increase your mic gain 3-4 dB over a standard dynamic element. Specifications: Output Connection: 4 pin XLR with Push-to-Talk
username
Show more
See More
4 hours ago The HM-10 microphones feature a built-in P.T.T. button or can be used in VOX mode. The boom clips can be attached to either an adjustable boom or to a TB-1 Table Base Mic Stand. The Heil HM-10-DUAL features both the HC-4 and HC-5 mic elements. The elements can be switched using the Wide-Narrow switch on the mic.
username
Show more
See More
7 hours ago HM-10 is a BLE module for embedded system to get BLE wireless communication with BLE capable devices (e.g. iPhone and iPad). It is fully configurable by a rich and well documented AT command-set and allows transparent data communication via …
username
Show more
See More
4 hours ago Oct 24, 2016 . CODE 1 – Routine Follow Officer. CODE 2 – Expedite Follow Officer. CODE 3 – Emergency Follow Officer. CODE 4 – No Further Assistance Needed. CODE 5 – Stakeout (Observation) CODE 6 – Out for Investigation. CODE 7 – Out of Service / Lunch Break. CODE 8 – Fire Alarm. CODE 12 – Report Disaster Damage.
Show more
See More
5 hours ago Description: HM-10 XD model has been redesigned with new HC-5x and HC-4x elements mounted on an acoustically tuned chamber to reproduce the popular narrow HC-4 response for DX work and a full smooth response of the HC-5 elements. Output Connection: 4 pin XLR with Push-to-Talk. Frequency Response HC-5X wide: 300 Hz – 8 kHz @ -72 dB.
Show more
See More
8 hours ago HM-10 has the latest 4.0 Bluetooth technology. There is no limit in sending bytes with HM-10. Power consumption is much less even in an operating state with this module. The HC10 module uses the 2.5GHz frequency band at the range of 100meter in an open area. It is useable as a Master or Slave just by disconnecting the connections.
username
Show more
See More
8 hours ago The Arduino has been badly cut without a shield in its connectivity to the outside world and so I ventured on the subject of Bluetooth, using the BLE module HM-10 (ZS-040) with Chip CC2541 (3 Euro). As it turned out later, the BLE module communicates via serial inputs and outputs, so that via smartphone apps ("ElegooBLE" or "Serial") the "code ...
username
Show more
See More
6 hours ago www.alibaba.com
Show more
See More
12 hours ago This redesign, HM-10 XD uses the new Heil Sound HC-5x and HC-4x elements mounted on an acoustically tuned chamber to reproduce the popular narrow HC-4 response for DX work and a full smooth response of the HC-5 elements. This allows users to operate a full range mic for everyday rag chew and instantly switch to a narrow DX element to punch …
username
Show more
See More
9 hours ago Login to your hamradio.com account below. If you do not have an account you can easily create a new account for free. Please feel free to contact us if you have any questions.
Show more
See More
4 hours ago Apr 11, 2022 . Heil Sound’s HM-10XD Microphone is a completely modernized redesign of the popular dual-element HM-10 "Gold Line." New HC-5x and HC-4x elements are mounted in an acoustically tuned chamber to reproduce the full, smooth response of the HC-5 element and the narrow HC-4 response for DX work.
username
Show more
See More
1 hours ago Jinan Huamao Technology Co., Ltd. User Guide Product Description: The Bluetooth Module (HM-10, HM-11) is a highly integrated Bluetooth BLE V4.0 module, designed for low energy, short-range wireless communication in the 2.4 GHz ISM band. Combined with the Bluetooth low energy protocol stack from Texas Instruments.
Show more
See More
Introduction HM-10 is a BLE module for embedded system to get BLE wireless communication with BLE capable devices (e.g. iPhone and iPad). It is fully configurable by a rich and well documented AT command-set and allows transparent data communication via serial UART (default baudrate 9600bps).
To check the modules name use AT+NAME?, or use an Android device and search for Bluetooth devices. The default name is HMsoft. This only works when the HM-10 is in Salve/Peripheral mode. When in Master/Central mode it does not broadcast its name. To get the modules address, use AT+ADDR? Change the name using AT+NAME.
Unless you desperately need long names I suggest you stay with the regular firmware. The HM-10 is a small 3.3v SMD Bluetooth 4.0 BLE module based on the TI CC2540 or CC2541 Bluetooth SOC (System On Chip).
HM-10 Programmable Pins. The HM-10 has 10 pins that can be user controlled, a couple are input only, the others can be input or output. Unfortunately, the pins we can control are not available on the breakout board so we need to attach a connection directly to the actual HM-10 (the small daughter board).